Denco supplier catalog / Accessory reference

COA IS40: BEA IS40 Dual Technology Sensor

The title identifies a BEA IS40 overhead activation/presence sensor using microwave and active infrared detection.

US source scopeUpdated 2026-09-13Independent Anderson reference

Match the whole number.

Denco catalog number: COA IS40. Keep the complete supplier number, including prefixes and suffixes. This identifies the supplier catalog listing.

A corresponding manufacturer part number or equivalent component has not been verified. Any manufacturer or designation stated by the supplier is labeled separately below.

Denco accessory source: COA IS40Product detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Denco accessory source: COA IS40Product detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Values apply to the exact identifier and scope in the cited source.
Supplier identification fact	The title identifies a BEA IS40 overhead activation/presence sensor using microwave and active infrared detection. Denco accessory source: COA IS40Product detail title and Description list · checked 2026-09-12 · Denco
Supplier identification fact	The source specifies an 8-16 foot mounting range for IS40 and separately directs the 6.5-11.5 foot range to IS40XL. Denco accessory source: COA IS40Product detail title and Description list · checked 2026-09-12 · Denco
Supplier identification fact	Up to 40 infrared detection spots and NEMA 4/IP65 enclosure ratings are described. Denco accessory source: COA IS40Product detail title and Description list · checked 2026-09-12 · Denco
Supplier identification fact	The manufacturer table names BEA. Denco accessory source: COA IS40Additional information: Manufacturer · checked 2026-09-12 · Denco
Scope and source limitation	The broad industrial-door statement does not identify an exact operator or monitoring interface. Environmental-immunity language is not an independently tested guarantee. The remote is not identified by an exact part number. Do not swap the IS40 and IS40XL mounting ranges. Denco accessory source: COA IS40Product detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

No equipment or component pairing is verified in this published reference. Match the exact equipment with Denco catalog source before selecting a component.

Direct replacement paths

No direct successor for COA IS40 is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Part or accessory brand

Narrow part or accessory choices by the complete number (optional)

Loading part or accessory choices…

Part or accessory

Selected: COA IS40 · Read its reference. Selection identifies a record; it does not confirm fitment.

Equipment or accessory brand

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Equipment market

Production date, if known

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

Denco accessory source: COA IS40Denco · US · checked 2026-09-12

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Denco catalog source and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status. Anderson provides repair service in its listed Connecticut communities.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.