Denco supplier catalog / Part reference

GDH 2000D: 2000D Direct Drive Chain Hoist

2000D direct-drive hoist for a 1-inch shaft.

US source scopeUpdated 2026-09-12Independent Anderson reference

Match the whole number.

Denco catalog number: GDH 2000D. Keep the complete supplier number, including prefixes and suffixes. This identifies the supplier catalog listing.

A corresponding manufacturer part number or equivalent component has not been verified. Any manufacturer or designation stated by the supplier is labeled separately below.

Denco hardware source: GDH 2000DProduct detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Denco hardware source: GDH 2000DProduct detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Values apply to the exact identifier and scope in the cited source.
Supplier identification fact	2000D direct-drive hoist for a 1-inch shaft. Denco hardware source: GDH 2000DProduct detail title and Description list · checked 2026-09-12 · Denco
Supplier identification fact	The source requires at least 5 3/8 inches of offset. Denco hardware source: GDH 2000DProduct detail title and Description list · checked 2026-09-12 · Denco
Supplier identification fact	Contents include 26 feet of hand chain, one keeper, two shaft collars and a 1/4-inch key. Denco hardware source: GDH 2000DProduct detail title and Description list · checked 2026-09-12 · Denco
Scope and source limitation	The minimum offset must remain visible; no reduced-drive ratio is supplied for this direct-drive model. Denco hardware source: GDH 2000DProduct detail title and Description list; explicit table cells where recorded · checked 2026-09-12 · Denco

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

No equipment or component pairing is verified in this published reference. Match the exact equipment with Denco catalog source before selecting a component.

Direct replacement paths

No direct successor for GDH 2000D is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Part or accessory brand

Narrow part or accessory choices by the complete number (optional)

Loading part or accessory choices…

Part or accessory

Selected: GDH 2000D · Read its reference. Selection identifies a record; it does not confirm fitment.

Equipment or accessory brand

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Equipment market

Production date, if known

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

Denco hardware source: GDH 2000DDenco · US · checked 2026-09-12

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Denco catalog source and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status. Anderson provides repair service in its listed Connecticut communities.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.