Denco supplier catalog / Independent reference
Denco supplier catalog parts
Browse exact identifiers, documented model scope and source-backed replacement paths.
Denco supplier catalog is the catalog issuer for these references. Catalog numbers are kept separate from manufacturer identities; read each source and edition before selecting.
- Catalog number: GDH 103088WD
GDH 103088WD: Commercial End Bearing Bracket, 5″
Commercial end-bearing bracket with 5-inch shaft offset.
- Catalog number: GDH 172845
GDH 172845: Disconnect Chain Hoist
Wall-mounted disconnect hoist with 4:1 reduction.
- Catalog number: DCCA PFL5-1
DCCA PFL5-1: Football Bearing, PFL5, 1″
Football bearing title gives designation PFL5 and size 1 inch.
- Catalog number: T SWAGKIT
T SWAGKIT: Swaging Kit
The swaging kit lists a metal case, one hand swager and one cable cutter.
- Catalog number: GDH 4-380-1/4
GDH 4-380-1/4: Sheave Pulley with Stud, 4″
The title identifies a 4-inch sheave pulley with a stud.
- Catalog number: GDH H0HS6794
GDH H0HS6794: Rubber Roller, 3″ Tire, 9″ Stem
The 3-inch tire is described as rubber-covered UHMW, with a 6202 sealed precision bearing.
- Catalog number: GDH 3055
GDH 3055: Keyed L Handle-Keyed Randomly
Random-keyed L-handle uses spacers for door thicknesses from 3/4 inch through 2 inches.
- Catalog number: GDH 194963
GDH 194963: Aluminum Bottom Brackets, 3″
Aluminum bottom-bracket listing named as 3 inches.
- Catalog number: GO 36773S.S
GO 36773S.S: 8 ft IntelliG carriage assembly
Denco identifies GO 36773S.S as its 8 ft IntelliG carriage-assembly listing. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH 3-11C
GDH 3-11C: Steel Roller, 3″ Extra Extra Long Stem
The supplier names this a 3-inch steel roller.
- Catalog number: LO 41D3058
LO 41D3058 — Denco Motor and bracket kit
Denco lists LO 41D3058 as a motor and bracket kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: LO K72-12508
LO K72-12508: Output Shaft Kit (1/3 & 1/2HP)
LO K72-12508 is an output-shaft kit listing with 1/3HP and 1/2HP headings. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH ORB21
GDH ORB21: Denco Operator Reinforcement Bracket-21″
Operator reinforcement bracket named as 21 inches.
- Catalog number: LO 41A4885-5
LO 41A4885-5 — Denco Belt-drive gear and sprocket assembly
Denco lists LO 41A4885-5 as its New Style belt-drive gear-and-sprocket assembly for models 2280, 2580, 2585, 3280 and 3585. This is supplier-reported applicability, not a verified manufacturer part-number mapping. Exact product market and production-revision applicability are not established; confirm installed equipment.
- Catalog number: GDH OPRFRCBRK21
GDH OPRFRCBRK21: 3 1/2″ Wide Operator Reinforcement Bracket-21″
Reinforcement bracket named as 3 1/2 inches wide and 21 inches long.
- Catalog number: GDH HWBRKARBHAL
GDH HWBRKARBHAL: ARB Adjustable Reinforcement Bracket-Half Hinge White
ARB half-hinge reinforcement bracket with adjustment for 18- to 24-inch sections.
- Catalog number: DCCA PFL32-11/4
DCCA PFL32-11/4: Football Bearing, PFL32, 1 1/4″
Football bearing title gives designation PFL32 and size 1 1/4 inch.
- Catalog number: GDH 3250
GDH 3250: Diecast Deadbolt-Keyed Randomly
Random-keyed diecast deadbolt has a powder-coated zinc case.
- Catalog number: GDH 180670
GDH 180670: Genie Operator Reinforcement Bracket, 18″
Named an 18-inch Genie operator reinforcement bracket in 10-gauge steel.
- Catalog number: GDH JRGCHNHOIST
GDH JRGCHNHOIST: J.R.G. Jackshaft Chain Hoist, 1″ Shaft
J.R.G. jackshaft-mounted hoist for a 1-inch shaft, restricted by the source to solid shafts.
- Catalog number: GDH P
GDH P: Non-Latching Exhaust Vent, 3″ X 1/4″
Non-latching exhaust vent with a 3-inch inside diameter for a 1/4-inch-thick door.
- Catalog number: GDH D
GDH D: Non-Latching Exhaust Vent, 3″ X 2″
Non-latching exhaust vent with an explicit 3-inch inside diameter.
- Catalog number: GDH CP-128
GDH CP-128: Clevis Pin, 5/16″ X 3″
Clevis pin with listed dimensions 5/16 inch by 3 inches.
- Catalog number: LO 7110345
LO 7110345: RPM Sensor Board for MT
LO 7110345 is an RPM-sensor board explicitly listed for MT in the heading. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: RC 97798
RC 97798: Marantec Logic Board, M4500E & M4700E
The offered assembly includes a logic board and terminal strip.
- Catalog number: LO 71-10324
LO 71-10324: Track Spacer Kit
LO 71-10324 is a track-spacer kit supplier listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH XXL
GDH XXL: Latching Exhaust Vent, 6″ X 3″
Latching exhaust vent with an explicit 6-inch inside diameter.
- Catalog number: LO 711550B22LGH
LO 711550B22LGH: Sprocket Kit, 22 Tooth, 1″ Bore
LO 711550B22LGH is a sprocket-kit supplier listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GO 38416A.S
GO 38416A.S: belt pulley and rail selection
The supplier identifies GO 38416A.S as a belt pulley or sprocket listing. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: DCCA UCP205-16
DCCA UCP205-16: Pillow Block Bearing, UCP205-16
Bore is explicitly listed as 1 inch.
- Catalog number: GDH 124772
GDH 124772: Plastic Roller, 3″ Tire, 7 1/4″ Stem
UHMW tire listed at 3 inches, with a 6202 sealed precision bearing.
- Catalog number: LO K72-12509
LO K72-12509: Output Shaft Kit (3/4 & 1 HP)
LO K72-12509 is an output-shaft kit listing whose heading states 3/4HP and 1HP. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 525-18
GDH 525-18: Commercial End Bearing Bracket, 3 3/8″
Commercial end-bearing bracket with 3 3/8-inch shaft offset.
- Catalog number: LO 041-0489-000
LO 041-0489-000 — Denco Push-button door-control replacement kit
Denco lists LO 041-0489-000 as a push-button door-control replacement kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: M TS15
M TS15: Top Seal
The supplier describes a top seal of black vinyl rubber with a 1-3/4-inch flap.
- Catalog number: GDH O&ELHBRACKE
GDH O&ELHBRACKE: O&E Low Headroom Kit
O&E low-headroom kit is described for extension-spring doors with a stated minimum of 7 inches of headroom.
- Catalog number: DCCA 8483608000
DCCA 8483608000: 1″ Tube Coupling
Nonadjustable 1-inch tube coupling with no keyway.
- Catalog number: DCCA SLD12'
DCCA SLD12': Standard Lift Drum, 12′
The supplier identifies a standard lift drum with 4-inch diameter.
- Catalog number: GDH DEN24W
GDH DEN24W: Denco Operator Reinforcement Bracket-24″ White
Operator reinforcement bracket named as 24 inches.
- Catalog number: GO 269660
GO 269660: channel-style chain pulley identification
Denco identifies GO 269660 as a chain pulley for a channel-style rail. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH 164375
GDH 164375: Residential End Bearing Bracket, 3 3/8″ Rounded
Rounded residential end-bearing bracket named in the 3 3/8-inch size.
- Catalog number: LO 41DB001-1
LO 41DB001-1 — Denco Circuit board
Denco lists LO 41DB001-1 as a circuit board. The description names 3500. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 134870
GDH 134870: Cast Iron Sheave Pulley, 3″
The title identifies a 3-inch cast-iron sheave pulley.
- Catalog number: LO 41AB050-2
LO 41AB050-2 — Denco Circuit board
Denco lists LO 41AB050-2 as a circuit board. The description names 3280. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 3050N
GDH 3050N: Dummy L-Handle
Dummy L-handle has blind mounting posts 1/2 inch long and a low-profile escutcheon.
- Catalog number: LO 711550B32LGH
LO 711550B32LGH: Sprocket Kit, 32 Tooth, 1″ Bore
LO 711550B32LGH is a sprocket-kit supplier listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: DCCA 1"FRADBRNG
DCCA 1"FRADBRNG: Flanged Radial Bearing, 1″
Named a 1-inch flanged radial ball bearing.
- Catalog number: M A165
M A165: Fusible Link Model A
Model A fusible link has a supplier-stated load range of 1 to 30 pounds, inclusive.
- Catalog number: GO 26013DS
GO 26013DS: curved door arm model selection
Denco identifies GO 26013DS as a curved door arm. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH PLBMSPRG27K
GDH PLBMSPRG27K: Plunger Bumper Spring, 27″
Plunger bumper spring is 27 inches long overall and has 15 inches of travel.
- Catalog number: LO 30B532
LO 30B532 — Denco Motor capacitor
Denco lists LO 30B532 as Motor capacitor. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: DCCA CNTRCUP114
DCCA CNTRCUP114: Torsion Shaft Center Coupling, 1-1/4″ to 1-1/4″
Adjustable torsion-shaft center coupling for 1 1/4-inch to 1 1/4-inch shaft connections.
- Catalog number: M B165
M B165: Fusible Link Model B
Model B fusible link has a supplier-stated load range of 1 to 10 pounds, inclusive.
- Catalog number: GO 37845R.S
GO 37845R.S: TriloG carriage assembly
Denco identifies GO 37845R.S as a TriloG carriage assembly and lists seven compatible model labels. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH ADJRFCBRKTW
GDH ADJRFCBRKTW: ARB Adjustable Operator Reinforcement Bracket-Full Hinge White
ARB adjustable reinforcement bracket with a full-hinge configuration.
- Catalog number: GDH 2000D
GDH 2000D: 2000D Direct Drive Chain Hoist
2000D direct-drive hoist for a 1-inch shaft.
- Catalog number: DCCA UCP207-20
DCCA UCP207-20: Pillow Block Bearing, UCP207-20
Bore is explicitly listed as 1 1/4 inch.
- Catalog number: LO 41A5658
LO 41A5658 — Denco Chain gear and sprocket assembly
Denco lists LO 41A5658 as a chain gear and sprocket assembly. The description names 2595, 3595, 3595S. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: LO 41AS050R2M
LO 41AS050R2M — Denco Receiver logic board with end panel
Denco lists LO 41AS050R2M as a receiver logic board with end panel. Its stated scope is 2005–2015 AC deluxe screw-drive units with Security+, 315 MHz and a purple learn button. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GO 20386RS
GO 20386RS: sequencer board and old-number identification
Denco lists supplier SKU GO 20386RS as a sequencer board. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GO 36773R.S
GO 36773R.S: 7 ft IntelliG carriage assembly
Denco identifies GO 36773R.S as its 7 ft IntelliG carriage-assembly listing. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH DEN18W
GDH DEN18W: Denco Operator Reinforcement Bracket-18″ White
Operator reinforcement bracket named as 18 inches.
- Catalog number: DCCA STLD8
DCCA STLD8: Standard Lift Drum, 8′
The supplier identifies a standard lift drum with 4-inch diameter.
- Catalog number: GDH 3-2-16
GDH 3-2-16: Precision Bearing End Bracket 5″
Precision-bearing end bracket has a stated 5-inch offset and measures 6 1/2 inches wide by 8 1/2 inches high.
- Catalog number: GDH REARTORSI
GDH REARTORSI: Commercial Flat End Bearing Plate
Commercial flat end-bearing plate for double-track, low-headroom rear-torsion applications.
- Catalog number: LO 41C4470
LO 41C4470 — Denco Chain gear and sprocket assembly
Denco lists LO 41C4470 as a chain gear and sprocket assembly. The description names ATS211, ATS211R. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: DCCA CF105
DCCA CF105: Torsion Shaft Center Coupling, 1″ to 1-1/4″
Adjustable torsion-shaft center coupling for 1-inch to 1 1/4-inch shaft connections.
- Catalog number: GDH 5/8HINGEBRK
GDH 5/8HINGEBRK: Denco Adjustable Hinge Bracket 5/8″
The adjustable hinge bracket is specified for a 5/8-inch roller-shaft diameter.
- Catalog number: GDH HBS2U
GDH HBS2U: Stainless Steel Bottom Bracket
The title names a stainless-steel bottom bracket; the list specifies 12-gauge steel.
- Catalog number: LO 41A4885-2
LO 41A4885-2 — Denco Belt-drive gear and sprocket assembly
Denco lists LO 41A4885-2 as its Old Style belt-drive gear-and-sprocket assembly for models 1270, 1280 and 1280R. This is supplier-reported applicability, not a verified manufacturer part-number mapping. Old Style does not establish a successor or interchangeability. Exact product market and production-revision applicability are not established; confirm installed equipment.
- Catalog number: GDH 2"10BXLSROL
GDH 2"10BXLSROL: Steel Roller, 2″ Extra Long Stem
The supplier names this a 2-inch steel roller.
- Catalog number: LO 711550B16LGH
LO 711550B16LGH: Sprocket Kit, 16 Tooth, 1″ Bore
LO 711550B16LGH is a sprocket-kit supplier listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH R2000
GDH R2000: 2000R Reduced Drive Chain Hoist, 1 1/4″ Shaft
2000R wall-mounted hoist for a 1 1/4-inch shaft with 4:1 reduction.
- Catalog number: DCCA 125934
DCCA 125934: 1″ Solid Shaft Coupling
Nonadjustable coupling named for a 1-inch solid shaft.
- Catalog number: GDH PL
GDH PL: Latching Exhaust Vent, 3″ X 1/4″
Latching exhaust vent with an explicit 3-inch inside diameter.
- Catalog number: LO K72-14130-1
LO K72-14130-1: Limit Shaft Kit L5; J, H & HJ
LO K72-14130-1 is a limit-shaft kit listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH E
GDH E: Non-Latching Exhaust Vent, 4″ X 2″
Non-latching exhaust vent with an explicit 4-inch inside diameter.
- Catalog number: GDH 3000
GDH 3000: Dummy T-Handle Set
Dummy T-handle set includes inner and outer handles plus mounting hardware.
- Catalog number: LO 21-14182
LO 21-14182: Transformer, 120/230V-20VA, 24VAC
LO 21-14182 is a transformer-kit listing with 120/230V,20VA and 24VAC designations. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: COA CSD1
COA CSD1: Cable-Safe Device
The Cable-Safe device is described as limiting cable slack.
- Catalog number: LO 12-10331
LO 12-10331: Flange Bearing, 3/4″x1-1/2″x1/8″
LO 12-10331 is a flange bearing with printed dimensions 3/4 inch x 1-1/2 inch x 1/8 inch. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 126645
GDH 126645: 200R Reduced (3:1) Drive Chain Hoist, 1″ Shaft
200R wall-mounted chain hoist for a 1-inch shaft with 3:1 reduction.
- Catalog number: GDH 3-45-5
GDH 3-45-5: Low Headroom Bottom Bracket, BB5
BB5 low-headroom bracket is 6 1/2 inches long by 2 7/8 inches wide.
- Catalog number: GDH 3-42-1K
GDH 3-42-1K: Bottom Bracket, BB6
BB6 bottom bracket is 10 5/8 inches long by 4 3/8 inches wide.
- Catalog number: DCCA D400-54K
DCCA D400-54K: High Lift Drum, 54″ w/ 9′ Max Door Height
The supplier identifies a high lift drum with 4-inch diameter.
- Catalog number: GDH 8040
GDH 8040: Complete Lock Package
Lock package includes a T-handle, plastic inner handle, automatic latches, latch cables, a striker, spacers and fasteners.
- Catalog number: LO 041C0279
LO 041C0279 — Denco Light socket
Denco describes LO 041C0279 as replacing references 004A1344, 4A1344, without exact model or revision limits. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: DCCA UCF207-20
DCCA UCF207-20: Precision Bearing, UCF207-20
Bore is explicitly listed as 1 1/4 inch.
- Catalog number: GDH CP-148
GDH CP-148: Clevis Pin, 3/8″ X 1 1/4″
Clevis pin with listed dimensions 3/8 inch by 1 1/4 inches.
- Catalog number: GDH 102088WD
GDH 102088WD: Commercial End Bearing Bracket, 4 3/8″
Commercial end-bearing bracket with 4 3/8-inch shaft offset.
- Catalog number: LO 41AC050-2
LO 41AC050-2 — Denco Circuit board
Denco lists LO 41AC050-2 as a circuit board. The description names 3265. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: LO K21-36793
LO K21-36793: Transformer, 3PH, 208/230/460V-20VA
LO K21-36793 is a 3PH tri-voltage transformer-kit listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 2-4(6200)N
GDH 2-4(6200)N: 6200 Bearing Roller-Short Stem
White nylon tire specified at 2-inch diameter with a zinc-plated 4-inch stem.
- Catalog number: GDH 229557
GDH 229557: EzLHR Conversion Kit
EzLHR is a three-piece conversion kit described for changing standard lift to low headroom without an outside-hookup configuration.
- Catalog number: GDH R
GDH R: Non-Latching Exhaust Vent, 4″ X 3″
Non-latching exhaust vent with an explicit 4-inch inside diameter.
- Catalog number: GDH UCF20516
GDH UCF20516: Precision Bearing, UCF205-16
Bore is explicitly listed as 1 inch.
- Catalog number: GDH DSUPRM3"LS
GDH DSUPRM3"LS: Denco Supreme 3″ Long Stem
Denco Supreme roller named in the 3-inch class; the tire is plastic.
- Catalog number: DCCA 2300K
DCCA 2300K: Standard Lift Drum, 32′
The supplier identifies a standard lift drum with 8-inch diameter.
- Catalog number: DCCA D850-132K
DCCA D850-132K: Vertical Lift Drum, 11′
The supplier identifies a vertical lift drum with 8-1/2-inch diameter.
- Catalog number: DCCA UCFL205-16
DCCA UCFL205-16: Precision Bearing, UCFL205-16
Bore is explicitly listed as 1 inch.
- Catalog number: DCCA 196131
DCCA 196131: Standard Lift Drum, 10’3″
The supplier identifies a standard lift drum with 4-inch diameter.
- Catalog number: DCCA UCFL207-20
DCCA UCFL207-20: Precision Bearing, UCFL207-20
Bore is explicitly listed as 1 1/4 inch.
- Catalog number: GDH 139589
GDH 139589: Heavy Duty Sheave Pulley, 3″
The title identifies a 3-inch heavy-duty sheave pulley.
- Catalog number: DCCA OMI-18VL-K
DCCA OMI-18VL-K: Vertical Lift Drum, 18′
The supplier identifies a vertical lift drum with 11-inch diameter.
- Catalog number: GDH 046DUOLEFT
GDH 046DUOLEFT: Flag Angle Bracket, Duo Dec
Duo Dec flag-angle bracket is described for the junction of vertical and horizontal track, attaching to the header and jamb.
- Catalog number: LO 041D8615
LO 041D8615 — Denco Collar kit
Denco describes LO 041D8615 as replacing references 041B6299, 41B6299, 041A6388, without exact model or revision limits. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: AP HAE00020
AP HAE00020: Gel Caps
AP HAE00020 is a gel-cap splice-connector listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: DCCA UCFL211-32
DCCA UCFL211-32: Precision Bearing, UCFL211-32
Bore is explicitly listed as 2 inch.
- Catalog number: LO 12-10029
LO 12-10029: Flange Bearing, 3/4″X1-1/4″X5/8″
LO 12-10029 is a flange bearing with printed dimensions 3/4 inch x 1-1/4 inch x 5/8 inch. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: DCCA 525-54K
DCCA 525-54K: High Lift Drum, 54″ w/ 14′ Max Door Height
The supplier identifies a high lift drum with 5-1/4-inch diameter.
- Catalog number: LO 24-24-6
LO 24-24-6: Relay, 24V, 10A (3PDT)
LO 24-24-6 is a relay listing with 24V,10A and 3PDT printed in the heading. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: DCCA OMI-164HL
DCCA OMI-164HL: High Lift Drum, 164″
The supplier identifies a high lift drum with 6-3/8-inch diameter.
- Catalog number: GDH BB6-LHR-REI
GDH BB6-LHR-REI: Low Headroom Bottom Bracket, BB6 Reinforced
Reinforced BB6 low-headroom bracket measures 10 15/16 inches high by 4 5/8 inches wide, with a 1 3/8-inch side flange.
- Catalog number: LO 050ACTB
LO 050ACTB — Denco Bluetooth receiver logic-board kit
Denco titles this listing 050ACTB, while its description identifies 050ACTBMC. The source does not explain their equivalence. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: AP HAE00040
AP HAE00040: Control Board
Denco identifies AP HAE00040 as a replacement control-board listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: LO 41A6102
LO 41A6102 — Denco Power door-lock kit
Denco lists LO 41A6102 as a power door-lock kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 3-45-6
GDH 3-45-6: Low Headroom Bottom Bracket, BB5 Reinforced
Reinforced BB5 low-headroom bottom bracket made from 11-gauge steel.
- Catalog number: GDH 7B.ROLLER
GDH 7B.ROLLER: 7 Ball Bearing Roller
Named a seven-ball-bearing roller; the list specifies a 2-inch tire and 4-inch stem.
- Catalog number: GDH ORB24
GDH ORB24: Denco Operator Reinforcement Bracket-24″
Operator reinforcement bracket named as 24 inches.
- Catalog number: GDH 51/2"PULLEY
GDH 51/2"PULLEY: Sheave Pulley with Bolt, 5-1/2″
The title identifies a 5-1/2-inch sheave pulley with a bolt.
- Catalog number: LO 050DCTB
LO 050DCTB — Denco Bluetooth receiver logic-board replacement kit
Denco lists LO 050DCTB as Bluetooth receiver logic-board replacement kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 186123
GDH 186123: Nylon Roller, 2″ Long Stem, 11 Ball
Named a 2-inch nylon roller; the tire is white and the bearing has eleven balls.
- Catalog number: GDH BB100K
GDH BB100K: Bottom Bracket, BB100
BB100 bottom bracket is 5 11/16 inches long by 2 11/16 inches wide.
- Catalog number: GDH 4"SHEAVEPUL
GDH 4"SHEAVEPUL: Heavy Duty Sheave Pulley, 4″
The title identifies a 4-inch heavy-duty sheave pulley.
- Catalog number: DCCA 124845
DCCA 124845: Flanged Radial Bearing, 1″ Heavy Duty
Named a 1-inch flanged radial ball bearing.
- Catalog number: LO K201050B2LP-
LO K201050B2LP-: Motor, 1/2HP, 115/230V, 1PH, Logic 5
LO K201050B2LP- is the literal supplier motor-kit SKU, including its trailing hyphen. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: AP 218189-01
AP 218189-01: Trolley Assembly
AP 218189-01 is a replacement trolley listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: LO 041-0155-000
LO 041-0155-000 — Denco Safety sensor mounting-bracket replacement kit
Denco lists LO 041-0155-000 as a safety sensor mounting-bracket replacement kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH OPRFRCBRK18
GDH OPRFRCBRK18: 3 1/2″ Wide Operator Reinforcement Bracket-18″
Reinforcement bracket named as 3 1/2 inches wide and 18 inches long.
- Catalog number: GDH CHAINJR114
GDH CHAINJR114: J.R. Jackshaft Chain Hoist, 1 1/4″ Shaft
J.R. jackshaft-mounted hoist for a 1 1/4-inch shaft, with 4:1 reduction and an external chain/sprocket drive.
- Catalog number: DCCA UCF206-20
DCCA UCF206-20: Precision Bearing, UCF206-20
Bore is explicitly listed as 1 1/4 inch.
- Catalog number: GDH HW-BRK-LHR2
GDH HW-BRK-LHR2: Low Headroom Top Bracket
Low-headroom top bracket is restricted to 2-inch track.
- Catalog number: LO 45DCT
LO 45DCT — Denco Circuit board
Denco lists LO 45DCT as a DC circuit board for chain or belt drives, with tri-band Security+2.0. The listing supplies no exact opener model or radio-frequency values; installed-equipment applicability remains unverified.
- Catalog number: GO 35426A
GO 35426A: 115 V transformer model selection
GO35426A is a transformer listing with a 115 V heading designation. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH 102434WD
GDH 102434WD: Commercial End Bearing Bracket, 6″
Commercial end-bearing bracket with 6-inch shaft offset.
- Catalog number: LO 41AS050-1
LO 41AS050-1 — Denco Circuit board
Denco lists LO 41AS050-1 as a circuit board. The description names 3110, 3220. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH DSUPRM3"SS
GDH DSUPRM3"SS: Denco Supreme 3″ Short Stem
Denco Supreme roller named in the 3-inch class; the tire is plastic.
- Catalog number: DCCA PFL32-1
DCCA PFL32-1: Football Bearing, PFL32, 1″
Football bearing title gives designation PFL32 and size 1 inch.
- Catalog number: GDH 14485K
GDH 14485K: Plunger Bumper Spring, 33″
Plunger bumper spring is 33 inches long overall and has 26 inches of travel.
- Catalog number: GDH JRGCHH11/4
GDH JRGCHH11/4: J.R.G. Jackshaft Chain Hoist, 1 1/4″ Shaft
J.R.G. jackshaft-mounted hoist for a 1 1/4-inch shaft, restricted by the source to solid shafts.
- Catalog number: AP HAE00049
AP HAE00049: Drive Sprocket Holder & Belt Clamp
AP HAE00049 is listed as a drive-sprocket holder and belt-clamp reference. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 2-7(6200)N
GDH 2-7(6200)N: 6200 Bearing Roller-Long Stem
Denco specifies a white nylon tire, 2-inch diameter and zinc-plated 7-inch stem.
- Catalog number: GDH 5"DOUBLE
GDH 5"DOUBLE: 2″ Double Strength Roller, Short Stem
The product has a double 2-inch tire and 5-inch stem.
- Catalog number: GDH 141406
GDH 141406: 2″ Keyed T Handle
Keyed T-handle is specified for a 2-inch-thick door.
- Catalog number: LO 29-31229
LO 29-31229: Relay, 1PH, 24VDC/30A (SPDT)
LO 29-31229 is a relay listing whose heading states 1PH,24VDC/30A andSPDT. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 180667
GDH 180667: Genie Operator Reinforcement Bracket, 21″
Named a 21-inch Genie operator reinforcement bracket in 10-gauge steel.
- Catalog number: GDH 3-2-7
GDH 3-2-7: Precision Bearing End Bracket 4 3/8″
Precision-bearing end bracket has a stated 4 3/8-inch offset and measures 6 inches wide by 8 1/2 inches high.
- Catalog number: GDH 3130
GDH 3130: End Stile Latch
End-stile latch is described for lockbar use or mounting at the end stile.
- Catalog number: GDH CP-84
GDH CP-84: Clevis Pin, 5/16″ X 1″
Clevis pin with listed dimensions 5/16 inch by 1 inch.
- Catalog number: GDH DORTRAKGUA
GDH DORTRAKGUA: Door Track Guards
Door-track guard is 48 inches tall and 7 inches wide, with a 10-inch-square base.
- Catalog number: GDH DSUPRM2"LS
GDH DSUPRM2"LS: Denco Supreme Roller-2″ Long Stem
Denco Supreme roller named in the 2-inch class; the tire is plastic.
- Catalog number: LO 41A5807-3
LO 41A5807-3 — Denco One-piece chain and cable replacement kit
Denco lists LO 41A5807-3 as a one-piece chain and cable replacement kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 180666
GDH 180666: Genie Operator Reinforcement Bracket, 24″
Named a 24-inch Genie operator reinforcement bracket made from 10-gauge steel.
- Catalog number: GDH 3" DOUBLE
GDH 3" DOUBLE: 3″ Double Strength Roller, Long Stem
The supplier specifies a double 3-inch tire with a 7-inch stem.
- Catalog number: GDH XL
GDH XL: Latching Exhaust Vent, 6″ X 2″
Latching exhaust vent with an explicit 6-inch inside diameter.
- Catalog number: GDH 8-3-10
GDH 8-3-10: Clevis Pin, 5/16″ X 1 1/4″
Clevis pin with listed dimensions 5/16 inch by 1 1/4 inches.
- Catalog number: DCCA D575-120K
DCCA D575-120K: High Lift Drum, 120″
The supplier identifies a high lift drum with 5-3/4-inch diameter.
- Catalog number: LO 12-19504
LO 12-19504: Flange Bearing, 1″
LO 12-19504 is a flange-bearing listing with a printed 1-inch size designation. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 3-2-8
GDH 3-2-8: Precision Bearing End Bracket 6″
Precision-bearing end bracket has a stated 6-inch offset and measures 7 1/2 inches wide by 8 1/2 inches high.
- Catalog number: LINO HAE00047
LINO HAE00047: Helical & Worm Gears
Denco lists LINO HAE00047 as a helical and worm gear replacement kit. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 3-40-1
GDH 3-40-1: Bottom Bracket, BB90
BB90 bottom bracket dimensions are 7 7/8 inches by 3 inches wide with a 1 3/8-inch side flange.
- Catalog number: GDH 2-9(6200)
GDH 2-9(6200): 6200 Bearing Roller-Extra Long Stem
Denco specifies a white nylon tire, 2-inch diameter and zinc-plated 9-inch stem.
- Catalog number: LO 41DJ001
LO 41DJ001 — Denco Circuit board
Denco lists LO 41DJ001 as a circuit board. The description names 3800. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH SHFTSUPPRTB
GDH SHFTSUPPRTB: Shaft Support Bracket-1″
Shaft-support bracket named in the 1-inch size for shaft operators.
- Catalog number: GDH DL
GDH DL: Latching Exhaust Vent, 3″ X 2″
Latching exhaust vent with an explicit 3-inch inside diameter.
- Catalog number: GDH 3"10ROLLRSS
GDH 3"10ROLLRSS: Steel Roller, 3″ Short Stem
The supplier names this a 3-inch steel roller.
- Catalog number: LO 41DJ002
LO 41DJ002 — Denco Circuit board
Denco lists LO 41DJ002 as a circuit board. The description names 8500. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH A
GDH A: Non-Latching Exhaust Vent, 5″ X 2″
Non-latching exhaust vent with an explicit 5-inch inside diameter.
- Catalog number: GDH 134283
GDH 134283: Slide Lock-European
Zinc-finished slide lock has a 1/2-inch slide bar and 2 1/8 inches of travel.
- Catalog number: LO 21-10340
LO 21-10340: Transformer, 115V, 24VAC, 20VA
LO 21-10340 is a transformer listing with printed 115V,24VAC and 20VA designations. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: LO 41A3589-3
LO 41A3589-3 — Denco Full belt assembly
Denco's LO 41A3589-3 listing uses a 7-foot full-belt-assembly designation and names models 1270, 1280 and 1280R. The length label does not establish a measured belt length or installed-door fit; confirm the exact configuration.
- Catalog number: RC 84284
RC 84284: Marantec Logic Board, M-Line & Q-Line
The supplier identifies this Marantec logic board for eight named operators: DC2500e, DC2500, DC3700, DC3700e, M4500, M4700, Q7500 and Q7700.
- Catalog number: LO 29-2
LO 29-2: Resistor, 25W, 10%, 2OHM
LO 29-2 is a resistor listing with printed 25W,10% and 2OHM designations. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH ORB18
GDH ORB18: Denco Operator Reinforcement Bracket-18″
Operator reinforcement bracket named as 18 inches.
- Catalog number: GDH DSUPRM2"SS
GDH DSUPRM2"SS: Denco Supreme 2″ Short Stem
Denco Supreme roller named in the 2-inch class; the tire is plastic.
- Catalog number: GDH CP-36
GDH CP-36: Clevis Pin, 1/4″ X 1″
Clevis pin with listed dimensions 1/4 inch by 1 inch.
- Catalog number: LO 41A3589-2
LO 41A3589-2 — Denco Full belt assembly
Denco's LO 41A3589-2 listing uses a 10-foot full-belt-assembly designation and independently names models 1270, 1280 and 1280R. The length label does not establish a measured belt length or installed-door fit; confirm the exact configuration.
- Catalog number: LO K75-10214
LO K75-10214: Door Arm, Straight
LO K75-10214 is a straight door-arm kit listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 2"10BLSROLL
GDH 2"10BLSROLL: Steel Roller, 2″ Long Stem
The supplier names this a 2-inch steel roller.
- Catalog number: LO K75-12870
LO K75-12870: Door Arm Assembly for MT, T & GT
LO K75-12870 is a door-arm assembly listing. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 3"10ROLLXLS
GDH 3"10ROLLXLS: Steel Roller, 3″ Extra Long Stem
The supplier names this a 3-inch steel roller.
- Catalog number: GO 39342R.S
GO 39342R.S: 120 V transformer model selection
GO39342R.S is a transformer listing with a 120 V heading designation. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: LO 41A5585-1
LO 41A5585-1 — Denco Chain gear and sprocket kit
Denco lists LO 41A5585-1 as a chain gear and sprocket kit. The description names 2575, 3575, 3575S, 3275. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 124773
GDH 124773: Rubber Roller, 3″ Tire, 7 1/4″ Stem
Rubber covers the 3-inch UHMW tire; a 6202 sealed precision bearing is listed.
- Catalog number: GDH DJS26
GDH DJS26: DJS Operator Reinforcing Bracket-26″
DJS reinforcement bracket named as 26 inches.
- Catalog number: GDH JR.CH.HOIST
GDH JR.CH.HOIST: J.R. Jackshaft Chain Hoist, 1″ Shaft
J.R. jackshaft-mounted hoist for a 1-inch shaft, with 4:1 reduction and an external chain/sprocket drive.
- Catalog number: GDH 193561
GDH 193561: Aluminum Bottom Brackets, 2″
Aluminum bottom-bracket listing named as 2 inches.
- Catalog number: GO 37561R.S
GO 37561R.S: 7 ft belt and bullet assembly
Denco identifies this listing as a belt and bullet assembly for a 7 ft belt rail. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: LO 45ACT
LO 45ACT — Denco Circuit board
Denco lists LO 45ACT as an AC belt-drive circuit board with tri-band Security+2.0. The listing supplies no exact opener model or radio-frequency values; installed-equipment applicability remains unverified.
- Catalog number: GDH 046DUDECAR
GDH 046DUDECAR: Flag Angle Bracket, Universal
Universal flag-angle bracket is described for the vertical/horizontal track junction, attaching to the header or jamb.
- Catalog number: GDH 103936
GDH 103936: Commercial End Bearing Bracket, 3 3/8″
Commercial end-bearing bracket with 3 3/8-inch shaft offset.
- Catalog number: LO 41A5434-13
LO 41A5434-13 — Denco Full belt assembly
Denco lists LO 41A5434-13 as the 8-foot full belt assembly. Its ten named model associations are conditional supplier statements; the label is not a measured belt length or a verified door-height limit.
- Catalog number: GDH 163852
GDH 163852: Stopping Bottom Bracket, 2″ Track
Stopping bottom bracket named for 2-inch track.
- Catalog number: DCCA 18'SLDRUM
DCCA 18'SLDRUM: Standard Lift Drum, 18′
The supplier identifies a standard lift drum with 5-1/2-inch diameter.
- Catalog number: LO 41AS050RIM
LO 41AS050RIM — Denco Receiver logic board with end panel
Denco SKU LO 41AS050RIM contains the letter I; its product title identifies 41AS050R1M with the digit 1. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: DCCA 125936
DCCA 125936: 1 1/4″ Solid Shaft Coupling
Nonadjustable coupling named for a 1 1/4-inch solid shaft.
- Catalog number: LO K201050B-2LP
LO K201050B-2LP: Motor, 1/2HP, 115/230V, 1PH, Logic 3 & 4
LO K201050B-2LP is a motor listing rated in its heading at 1/2HP, 115/230V and 1PH. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 5"DDPULLEY
GDH 5"DDPULLEY: Sheave Pulley with Shaft, 5-1/2″
The title identifies a 5-1/2-inch sheave pulley with a shaft.
- Catalog number: LO 29B129
LO 29B129 — Denco Belt clip for a spliced opener belt
Denco lists LO 29B129 as a belt clip for a spliced opener belt. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH G
GDH G: Non-Latching Exhaust Vent, 4″ X 1/4″
Non-latching exhaust vent with an explicit 4-inch inside diameter.
- Catalog number: GDH QUICKCLOSEF
GDH QUICKCLOSEF: Quick Closing Fixtures
Quick-closing fixtures measure 18 3/16 inches long by 2 7/8 inches wide.
- Catalog number: GDH 173113
GDH 173113: Nylon Roller 2″ Short Stem, 11 Ball
Named a 2-inch nylon roller; the tire is white and the bearing has eleven balls.
- Catalog number: DCCA 134954
DCCA 134954: Flanged Radial Bearing, 1 1/4″
Named a 1 1/4-inch flanged radial ball bearing.
- Catalog number: LO 050DCJCWFSD
LO 050DCJCWFSD: Logic Board, 050DCJCWFSD
LO 050DCJCWFSD is the supplier logic-board listing; 050DCJCWFSD is separately printed in the heading. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 2"10BSSROLL
GDH 2"10BSSROLL: Steel Roller, 2″ Short Stem
Named a 2-inch steel roller with ten ball bearings and deep-groove machined races.
- Catalog number: GDH ADJRFRCBRKT
GDH ADJRFRCBRKT: ARB Adjustable Operator Reinforcement Bracket-Full Hinge
ARB adjustable reinforcement bracket with a full-hinge configuration.
- Catalog number: LO 41B6228
LO 41B6228 — Denco Mounting bracket
Denco lists SKU LO 41B6228 as a mounting bracket and separately names 41C0902 as an alternate designation. No exact opener model is stated. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH ADJRBRKT1/2
GDH ADJRBRKT1/2: ARB Adjustable Operator Reinforcement Bracket-Half Hinge
ARB adjustable reinforcement bracket with a half-hinge configuration.
- Catalog number: GDH DJS50
GDH DJS50: DJS Operator Reinforcing Bracket-50″
DJS reinforcement bracket named as 50 inches.
- Catalog number: AP HAE00004
AP HAE00004: Limit Switch Assembly
Denco identifies AP HAE00004 as a replacement limit-switch assembly. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GDH 160278
GDH 160278: Slide Lock-Silent 2″
Silent slide lock is restricted to 2-inch track.
- Catalog number: GDH DEN 21W
GDH DEN 21W: Denco Operator Reinforcement Bracket-21″ White
Operator reinforcement bracket named as 21 inches.
- Catalog number: GDH 7"DOUBLE
GDH 7"DOUBLE: 2″ Double Strength Roller, Long Stem
The product has a double 2-inch tire and 7-inch stem.
- Catalog number: GDH UNSLIDELOCK
GDH UNSLIDELOCK: Slide Lock-Universal
Zinc-finished slide lock has supplier-stated applications to 2-inch and 3-inch track.
- Catalog number: LO 041-0136
LO 041-0136 — Denco Safety reversing-sensor kit
Denco lists LO 041-0136 as Safety reversing-sensor kit. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: LO 41A6408
LO 41A6408 — Denco Absolute encoder and travel-module replacement kit
Denco SKU LO 41A6408 is listed under designation 41B8861. The source also names prior reference 41A6118 without exact model or revision limits. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH OPRFRCBRK24
GDH OPRFRCBRK24: 3 1/2″ Wide Operator Reinforcement Bracket-24″
Reinforcement bracket named as 3 1/2 inches wide and 24 inches long.
- Catalog number: GDH 3"10BROLLLS
GDH 3"10BROLLLS: Steel Roller, 3″ Long Stem
The supplier names this a 3-inch steel roller.
- Catalog number: DCCA 124871
DCCA 124871: Flanged Radial Bearing, 1 1/4″ Heavy Duty
Named a heavy-duty flanged radial bearing in the 1 1/4-inch size.
- Catalog number: AP 21-5230
AP 21-5230: Transformer, 208/240V, 24VAC, 40VA
AP 21-5230 is a transformer listing with 208/240V,24VAC and 40VA printed in its heading. Denco supplier assertion for the US reference catalog; confirm the installed equipment and applicable revision. This is not manufacturer engineering verification.
- Catalog number: GO 37561S.S
GO 37561S.S: 8 ft belt and bullet assembly
Denco identifies this listing as a belt and bullet assembly for a 8 ft belt rail. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: GDH TSSADDLE
GDH TSSADDLE: Torsion Spring Saddle
The supplier describes a support saddle for torsion springs with inside diameter of at least 5-1/4 inches.
- Catalog number: GDH 103415
GDH 103415: Residential End Bearing Bracket, 3 3/8″
Residential end-bearing bracket named in the 3 3/8-inch size.
- Catalog number: GDH 2000R
GDH 2000R: 2000R Reduced Drive Chain Hoist, 1″ Shaft
2000R wall-mounted hoist for a 1-inch shaft with 4:1 reduction.
- Catalog number: LO 41A5434-11
LO 41A5434-11 — Denco Full belt assembly
Denco lists LO 41A5434-11 as the 7-foot full belt assembly. Its ten named model associations are conditional supplier statements; the label is not a measured belt length or a verified door-height limit.
- Catalog number: GDH SFTSPBRK114
GDH SFTSPBRK114: Shaft Support Bracket-1 1/4″
Shaft-support bracket named in the 1 1/4-inch size for shaft operators.
- Catalog number: LO 41AC075-2S
LO 41AC075-2S — Denco Circuit board for a single-capacitor opener configuration
Denco lists LO 41AC075-2S as Circuit board for a single-capacitor opener configuration. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH 7/16HINGEBR
GDH 7/16HINGEBR: Denco Adjustable Hinge Bracket 7/16″
The adjustable hinge bracket is specified for a 7/16-inch roller-shaft diameter.
- Catalog number: GO 36254R
GO 36254R: chain-drive T-rail carriage
Denco describes GO 36254R as a chain-drive T-rail carriage for four explicitly named ProMax configurations. Denco's US supplier listing; product-specific market/revision applicability is not established. Supplier statements are not manufacturer engineering verification.
- Catalog number: LO 41AC050-1
LO 41AC050-1 — Denco Circuit board
Denco lists LO 41AC050-1 as a circuit board. The description names 3245, 3255. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
- Catalog number: GDH B
GDH B: Non-Latching Exhaust Vent, 5″ X 1/4″
Non-latching exhaust vent with an explicit 5-inch inside diameter.
- Catalog number: GDH PLNGBMPR15K
GDH PLNGBMPR15K: Plunger Bumper Spring, 15″
Plunger bumper spring is 15 inches long overall and has 6 inches of travel.
- Catalog number: DCCA PFL5-1-1/4
DCCA PFL5-1-1/4: Football Bearing, PFL5, 1 1/4″
Football bearing title gives designation PFL5 and size 1 1/4 inch.
- Catalog number: DCCA CNTRCUPL1'
DCCA CNTRCUPL1': Torsion Shaft Center Coupling, 1″ to 1″
Adjustable torsion-shaft center coupling for 1-inch to 1-inch shaft connections.
- Catalog number: GDH H
GDH H: Non-Latching Exhaust Vent, 3″ X 3″
Non-latching exhaust vent with an explicit 3-inch inside diameter.
- Catalog number: LO 050DCTBFLK*
LO 050DCTBFLK* — Denco Bluetooth receiver logic-board replacement kit
Denco titles this listing 050DCTBFLK, while its description identifies 050DCTBFLKMC. Supplier SKU LO 050DCTBFLK* also carries an unexplained asterisk. Denco's US supplier listing; exact product market/revision applicability is not established; confirm installed equipment.
This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status.
A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.