Connecticut Garage Door Repair & InstallationOpen 24 Hours — 7 Days a Week
Anderson Garage Door Service
Call for Service(203) 902-3902Call anytime · appointments based on current availability

Miller Edge / Accessory reference

Miller Edge LED-PHXRS-K8: Motion-activated LED kit for rolling-steel doors

LED-PHXRS-K8: Motion-activated LED kit for rolling-steel doors

US source scopeUpdated 2026-09-14Independent Anderson reference

Match the whole number.

Manufacturer identifier: LED-PHXRS-K8. Keep every character when comparing it with your label or paperwork. A similar number does not establish the same component.

Values apply to the exact identifier and scope in the cited source.
Exact applicationThis rolling-steel kit is listed for opening width of 9 ft 0 in or more. Preserve the SD/RS distinction.
Door restrictionFor standard and high-performance commercial doors; the manufacturer does not recommend this system for high-speed doors.
Activation and chargingAn accelerometer activates the lighting independently of the door operator. Charging uses aligned inductive pads when the door is closed.
Strip indicationsOpen: green for about six seconds, then off. Closed: red for about six seconds, then off. Opening: red/amber scanner pattern; closing: red scanner pattern.
Power identificationReceiver battery: rechargeable 3.7 V 800 mAh lithium-ion. Transmitter supply: 100-240 V AC, 50/60 Hz input and 5 V DC 1.5 A output.
Temperature limitsCharging range: 32-113 F (0-45 C). Discharge range: -4-140 F (-20-60 C). These are separate limits.
Length and mountingLED strip: 7 ft 10.25 in; mounting channel: 8 feet. Rolling-steel kit additionally uses bottom-bar clips and a door-guide mounting arrangement. The sheet notes off-center lighting on doors wider than 12 feet.
Protection boundaryIP68 applies to the LED-strip component; NEMA 4 applies to the Power RX and TX enclosures.
Selection boundaryThis visual alert does not establish sensing or monitored entrapment protection. Confirm the exact mechanical kit, charging alignment and environment; no SD/RS interchangeability is established.

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

No equipment or component pairing is verified in this published reference. Match the exact equipment with Miller Edge official support before selecting a component.

Direct replacement paths

No direct successor for LED-PHXRS-K8 is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Loading part or accessory choices…

Selected: LED-PHXRS-K8 · Read its reference. Selection identifies a record; it does not confirm fitment.

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

  1. Phoenix LED-PHX motion-activated LED alert systemMiller Edge · US · checked 2026-09-14 · LED-PHX_Spec_20260806

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Miller Edge official support and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status. Anderson provides repair service in its listed Connecticut communities.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.

Call (203) 902-3902 — Check Today's Availability