Garage Door Repair & InstallationOpen 24 Hours — 7 Days a Week
Anderson Garage Door Service
Call for Service
(203) 902-3902

Miller Edge / Accessory reference

Miller Edge CPT210: Sensing-edge profile and configuration selection

CPT210 is a field-configurable single-T sensing-edge profile for the rolling counter shutters and grilles described in its specification. Bulk extrusion, edge kits and end kits are distinct purchasing forms. Its documented end-kit choices are two-wire configurations; the sheet does not list a four-wire option.

US source scopeUpdated 2026-09-15Independent Anderson reference

Match the whole number.

Manufacturer identifier: CPT210. Keep every character when comparing it with your label or paperwork. A similar number does not establish the same component.

Values apply to the exact identifier and scope in the cited source.
Profile applicationCommercial rolling counter shutters and grilles; the sheet also lists separate gate and industrial uses.
View source and citation details
Mounting arrangementField-configurable single-T extrusion with separate end kits and channel selection.
View source and citation details
Profile width0.88 inch in the specification drawing
View source and citation details
Profile height1.14 inches in the specification drawing
View source and citation details
MaterialsFlexible PVC and conductive-polymer extrusion with molded-polymer ends.
View source and citation details
Maximum electric-edge length50 feet
View source and citation details
Outlet selectionUniversal end plug; the listed lead is 12 inches, 22 gauge.
View source and citation details
Documented configuration choices2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 2-wire non-monitored
View source and citation details
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Documented configuration choices · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
Selection boundaryA profile name does not specify the complete configured edge. Confirm the required length, mounting geometry, outlet, monitored or non-monitored switch configuration, termination and exact operator requirements with Miller Edge. This reference does not establish fitment for every door or opener.
View source and citation details
Source limitationThe 8.2K, 10K, diode-capacitor and non-monitored configurations are separate end-kit choices. The sheet does not list a four-wire monitored version.
View source and citation details
Source limitationME120-C5 is also pictured, but its previously reviewed application is a gate sweep edge. It is excluded from the door mounting graph.
View source and citation details
Source limitationBulk extrusion, edge kit and end kit are distinct purchasing forms; no complete kit number or cross-profile end-kit interchangeability is inferred.
View source and citation details

Compare the single-T shutter and grille profiles

Compare profile height, electric-edge length and configuration choices together. CPT210 uses field-selected end kits; ME110 and ME111 list four-wire options that CPT210 does not. Shared mounting channels do not establish edge or end-kit interchangeability.

Separate references with their own source scope. This comparison establishes no replacement or interchangeability.
Exact referenceRecorded distinctions
CPT210

This reference

Miller Edge CPT210: Sensing-edge profile and configuration selection

CPT210 is a field-configurable single-T sensing-edge profile for the rolling counter shutters and grilles described in its specification. Bulk extrusion, edge kits and end kits are distinct purchasing forms. Its documented end-kit choices are two-wire configurations; the sheet does not list a four-wire option.

View sources and citation details
  • Profile application: Commercial rolling counter shutters and grilles; the sheet also lists separate gate and industrial uses.
    View source and citation details
  • Mounting arrangement: Field-configurable single-T extrusion with separate end kits and channel selection.
    View source and citation details
  • Profile width: 0.88 inch in the specification drawing
    View source and citation details
  • Profile height: 1.14 inches in the specification drawing
    View source and citation details
  • Maximum electric-edge length: 50 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 2-wire non-monitored
    View source and citation details
    • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Documented configuration choices · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
  • Source limitation: The 8.2K, 10K, diode-capacitor and non-monitored configurations are separate end-kit choices. The sheet does not list a four-wire monitored version.
    View source and citation details
  • Source limitation: ME120-C5 is also pictured, but its previously reviewed application is a gate sweep edge. It is excluded from the door mounting graph.
    View source and citation details
  • Source limitation: Bulk extrusion, edge kit and end kit are distinct purchasing forms; no complete kit number or cross-profile end-kit interchangeability is inferred.
    View source and citation details

Read CPT210’s pairing status and source conditions →

ME110

Miller Edge ME110: Sensing-edge profile and configuration selection

ME110 is a single-T slide-in sensing-edge profile for the rolling counter shutters and grilles described by Miller Edge, with a 7/8-inch-wide, 3/4-inch-high body. Its 50-foot maximum electric-edge length and 30-foot Air-Wave limit apply to different configurations. Shared channels with ME111 do not establish replacement equivalence.

View sources and citation details
  • Profile application: Rolling counter shutters and grilles; the sheet describes doors up to 1 inch thick.
    View source and citation details
  • Mounting arrangement: Slide-in profile with a single central T mounting feature.
    View source and citation details
  • Profile width: 7/8 inch
    View source and citation details
  • Profile height: 3/4 inch
    View source and citation details
  • Maximum electric-edge length: 50 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored; Air-Wave non-monitored
    View source and citation details
  • Source limitation: Do not confuse the maximum electric length with the 30-foot Air-Wave length limit.
    View source and citation details

Read ME110’s pairing status and source conditions →

ME111

Miller Edge ME111: Sensing-edge profile and configuration selection

ME111 is a taller slide-in sensing-edge profile for rolling counter shutters and grilles, including uneven counter or floor surfaces. Its 7/8-inch-wide, 1-1/2-inch-high body differs from ME110 despite the shared channel family. Confirm the required length, outlet and electrical configuration for the complete edge.

View sources and citation details
  • Profile application: Tall edge for rolling counter shutters and grilles, including uneven counter or floor surfaces.
    View source and citation details
  • Mounting arrangement: Slide-in profile using the listed ME110 channel family; its taller body is a separate edge identity.
    View source and citation details
  • Profile width: 7/8 inch
    View source and citation details
  • Profile height: 1-1/2 inches
    View source and citation details
  • Maximum electric-edge length: 100 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored; Air-Wave non-monitored
    View source and citation details
  • Source limitation: Sharing mounting channels with ME110 does not establish edge replacement equivalence.
    View source and citation details

Read ME111’s pairing status and source conditions →

A specification absent from one reference is not established by the other. Keep the exact identifier, configuration and cited revision when comparing.

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

A component pairing applies only to the listed items and source conditions. It does not establish suitability for an installed opener or compatibility through another component.

Source statements and their exact conditions. Use the checker below to compare equipment or a component.
Equipment or component / relationshipEvidence and conditions
EIM-101

Documented compatibility

From CPT210 to EIM-101.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

CPT210 is within the explicitly listed non-monitored Miller Edge CPT input group for EIM-101.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire non-monitored
  • Confirm the legacy relay-logic operator, 24 V control-circuit context and actual edge input. Non-monitored output is not a substitute where monitored entrapment protection is required.
FSIS-35P-4

Documented compatibility

From CPT210 to FSIS-35P-4.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

CPT210 is in the explicitly named Miller Edge 2/4-wire sensing-edge input group for FSIS-35P-4.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire non-monitored
  • Confirm exact input configuration and the full circuit with the responsible qualified designer. The group statement does not approve the edge for a classified location, establish intrinsic safety of the installation, or certify a complete door safety function.
MEL-K20

Documented compatibility

From CPT210 to MEL-K20.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

CPT210 falls within the MEL-K20 sheet's explicit T2 (10K) monitored sensing-edge group only with the matching configured termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • The source qualifies monitored operation with its UL325-2010 listed commercial door/gate operator context. The specific installed operator still requires confirmation; this group relationship is only the sensing-edge input scope.
  • This does not establish MEL-II or RBand compatibility, present product availability, or an installed-operator approval.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact profile monitored 10K membership · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
  • Monitored Edge Link MEL-K20MEL-K20_Spec_20150303, PDF page 1: Any T2 (10K) monitored edge group and listed-operator condition · checked 2026-09-14 · MEL-K20_Spec_20150303 · Miller Edge
SM-101

Documented compatibility

From CPT210 to SM-101.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

CPT210 is within the documented Miller Edge sensing-edge group for SM-101 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: Diode capacitor
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge
SM-102

Documented compatibility

From CPT210 to SM-102.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

CPT210 is within the documented Miller Edge sensing-edge group for SM-102 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge
ME110-C

Documented compatibility

From ME110-C to CPT210.

Conditional

ME110-C is a source-listed mounting channel for CPT210; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact optional mounting channel · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
ME110-C2

Documented compatibility

From ME110-C2 to CPT210.

Conditional

ME110-C2 is a source-listed mounting channel for CPT210; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact optional mounting channel · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
ME110-C3

Documented compatibility

From ME110-C3 to CPT210.

Conditional

ME110-C3 is a source-listed mounting channel for CPT210; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact optional mounting channel · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
ME120-C

Documented compatibility

From ME120-C to CPT210.

Conditional

ME120-C is a source-listed mounting channel for CPT210; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact optional mounting channel · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge
ME120-PC

Documented compatibility

From ME120-PC to CPT210.

Conditional

ME120-PC is a source-listed mounting channel for CPT210; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
  • Miller Edge CPT210 sensing edgeCPT210_spec_20251112, PDF page 2: Exact optional mounting channel · checked 2026-09-13 · CPT210_spec_20251112 · Miller Edge

Direct replacement paths

No direct successor for CPT210 is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Loading part or accessory choices…

Selected: CPT210 · Read its reference. Selection identifies a record; it does not confirm fitment.

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

  1. Miller Edge CPT210 sensing edgeMiller Edge · US · checked 2026-09-13 · CPT210_spec_20251112
  2. Electrical Interface Module EIM-101Miller Edge · US · checked 2026-09-14 · EIM-101_V01
  3. FSIS-35P-4 intrinsically safe relay controllerMiller Edge · US · checked 2026-09-14 · FSIS-35P-4_20211111
  4. Monitored Edge Link MEL-K20Miller Edge · US · checked 2026-09-14 · MEL-K20_Spec_20150303
  5. Signature Module SM-101 and SM-102Miller Edge · US · checked 2026-09-13 · SM101-SM102_20230407

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Miller Edge official support and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.