Garage Door Repair & InstallationOpen 24 Hours — 7 Days a Week
Anderson Garage Door Service
Call for Service
(203) 902-3902

Miller Edge / Accessory reference

Miller Edge ME112: Sensing-edge profile and configuration selection

ME112 is a double-T slide-in sensing-edge profile for the commercial sectional-door arrangement described with a 1-3/8-inch surface and accepting bottom bar. The ME112 component and the Clima-GUARD assembly have different dimensions. Air-Wave and pneumatic availability remain unresolved: the length row mentions options absent from the configuration list.

US source scopeUpdated 2026-09-15Independent Anderson reference

Match the whole number.

Manufacturer identifier: ME112. Keep every character when comparing it with your label or paperwork. A similar number does not establish the same component.

Values apply to the exact identifier and scope in the cited source.
Profile applicationCommercial sectional doors; the sheet describes a 1-3/8-inch surface with an accepting bottom bar.
View source and citation details
Mounting arrangementDouble-T slide-in mounting.
View source and citation details
Profile width1-5/16 inches
View source and citation details
Profile height1-1/2 inches
View source and citation details
MaterialsFlexible PVC edge and high-density PVC channels.
View source and citation details
Maximum electric-edge length100 feet
View source and citation details
Outlet selectionLeft, right, end or top.
View source and citation details
Documented configuration choices2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored
View source and citation details
Selection boundaryA profile name does not specify the complete configured edge. Confirm the required length, mounting geometry, outlet, monitored or non-monitored switch configuration, termination and exact operator requirements with Miller Edge. This reference does not establish fitment for every door or opener.
View source and citation details
Source limitationThe maximum-length row mentions Air-Wave and pneumatic variants, but the options list does not list those variants. Keep those configurations unresolved; do not infer availability from the shared length row.
View source and citation details

Compare the Clima-GUARD assembly and its ME112 component

Clima-GUARD combines an ME112 edge, an LS-0107 loop seal and a double-slot channel. Its overall assembly dimensions are not ME112 component dimensions. Air-Wave availability remains unresolved in the cited configuration lists; a shared length row does not verify that option.

Separate references with their own source scope. This comparison establishes no replacement or interchangeability.
Exact referenceRecorded distinctions
Clima-GUARD

Miller Edge Clima-GUARD: Sensing-edge profile and configuration selection

Clima-GUARD combines an ME112 sensing edge, an LS-0107 loop seal and a double-slot channel for the door arrangements described by Miller Edge. Its overall assembly dimensions differ from the ME112 component dimensions. Air-Wave availability remains unresolved in the cited configuration list.

View sources and citation details
  • Profile application: Commercial sectional doors and some high-performance door arrangements; exact installed type remains necessary.
    View source and citation details
  • Mounting arrangement: ME112 sensing edge combined with an LS-0107 loop seal and a double-slot channel.
    View source and citation details
  • Profile width: 2-1/4 inches at the illustrated assembly
    View source and citation details
  • Profile height: Approximately 3 inches overall in the illustrated assembly
    View source and citation details
  • Maximum electric-edge length: 100 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored
    View source and citation details
  • Source limitation: Clima-GUARD is a described assembly, not an alias for the ME112 component inside it. LS-0107 is the separately labelled loop seal.
    View source and citation details
  • Source limitation: The maximum-length row mentions Air-Wave, but the options list only explicitly identifies electric configurations. No unqualified Air-Wave configuration is approved.
    View source and citation details

Read Clima-GUARD’s pairing status and source conditions →

ME112

This reference

Miller Edge ME112: Sensing-edge profile and configuration selection

ME112 is a double-T slide-in sensing-edge profile for the commercial sectional-door arrangement described with a 1-3/8-inch surface and accepting bottom bar. The ME112 component and the Clima-GUARD assembly have different dimensions. Air-Wave and pneumatic availability remain unresolved: the length row mentions options absent from the configuration list.

View sources and citation details
  • Profile application: Commercial sectional doors; the sheet describes a 1-3/8-inch surface with an accepting bottom bar.
    View source and citation details
  • Mounting arrangement: Double-T slide-in mounting.
    View source and citation details
  • Profile width: 1-5/16 inches
    View source and citation details
  • Profile height: 1-1/2 inches
    View source and citation details
  • Maximum electric-edge length: 100 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored
    View source and citation details
  • Source limitation: The maximum-length row mentions Air-Wave and pneumatic variants, but the options list does not list those variants. Keep those configurations unresolved; do not infer availability from the shared length row.
    View source and citation details

Read ME112’s pairing status and source conditions →

A specification absent from one reference is not established by the other. Keep the exact identifier, configuration and cited revision when comparing.

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

A component pairing applies only to the listed items and source conditions. It does not establish suitability for an installed opener or compatibility through another component.

Source statements and their exact conditions. Use the checker below to compare equipment or a component.
Equipment or component / relationshipEvidence and conditions
ME112-C3

Documented compatibility

From ME112-C3 to ME112.

Conditional

ME112-C3 is a source-listed mounting channel for ME112; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
ME112-C7

Documented compatibility

From ME112-C7 to ME112.

Conditional

ME112-C7 is a source-listed mounting channel for ME112; mechanical selection only.

Applies only within this source scope
  • Market: US
  • Match the actual edge profile, channel geometry and required length. This mechanical pairing does not establish electrical monitoring or installed-operator compatibility.
FSC-57-115VAC

Documented compatibility

From ME112 to FSC-57-115VAC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the exact four-wire Miller Edge input group listed for FSC-57-115VAC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. This exact model specifies 115 V AC.
FSC-57-24VDC

Documented compatibility

From ME112 to FSC-57-24VDC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the exact four-wire Miller Edge input group listed for FSC-57-24VDC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. The VDC model and first-page list say 24 V DC; the table also says AC. AC acceptance is unresolved.
FSIS-35P-4

Documented compatibility

From ME112 to FSIS-35P-4.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is in the explicitly named Miller Edge 2/4-wire sensing-edge input group for FSIS-35P-4.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm exact input configuration and the full circuit with the responsible qualified designer. The group statement does not approve the edge for a classified location, establish intrinsic safety of the installation, or certify a complete door safety function.
MEL-K20

Documented compatibility

From ME112 to MEL-K20.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 falls within the MEL-K20 sheet's explicit T2 (10K) monitored sensing-edge group only with the matching configured termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • The source qualifies monitored operation with its UL325-2010 listed commercial door/gate operator context. The specific installed operator still requires confirmation; this group relationship is only the sensing-edge input scope.
  • This does not establish MEL-II or RBand compatibility, present product availability, or an installed-operator approval.
  • Miller Edge ME112 sensing edgeME112_20201218, PDF page 2: Exact profile monitored 10K membership · checked 2026-09-13 · ME112_20201218 · Miller Edge
  • Monitored Edge Link MEL-K20MEL-K20_Spec_20150303, PDF page 1: Any T2 (10K) monitored edge group and listed-operator condition · checked 2026-09-14 · MEL-K20_Spec_20150303 · Miller Edge
RT6-115VAC

Documented compatibility

From ME112 to RT6-115VAC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the exact four-wire Miller Edge input group listed for RT6-115VAC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. This exact model specifies 115 V AC.
RT6-24VDC

Documented compatibility

From ME112 to RT6-24VDC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the exact four-wire Miller Edge input group listed for RT6-24VDC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. The VDC model and first-page list say 24 V DC; the table also says AC. AC acceptance is unresolved.
SM-101

Documented compatibility

From ME112 to SM-101.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the documented Miller Edge sensing-edge group for SM-101 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: Diode capacitor
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge ME112 sensing edgeME112_20201218, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · ME112_20201218 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge
SM-102

Documented compatibility

From ME112 to SM-102.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

ME112 is within the documented Miller Edge sensing-edge group for SM-102 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge ME112 sensing edgeME112_20201218, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · ME112_20201218 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge

Direct replacement paths

No direct successor for ME112 is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Loading part or accessory choices…

Selected: ME112 · Read its reference. Selection identifies a record; it does not confirm fitment.

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

  1. FSIS-35P-4 intrinsically safe relay controllerMiller Edge · US · checked 2026-09-14 · FSIS-35P-4_20211111
  2. Miller Edge ME112 sensing edgeMiller Edge · US · checked 2026-09-13 · ME112_20201218
  3. Monitored Edge Link MEL-K20Miller Edge · US · checked 2026-09-14 · MEL-K20_Spec_20150303
  4. RT6 and FSC-57 safety relay controllersMiller Edge · US · checked 2026-09-14 · RT6_FSC-57_20211111
  5. Signature Module SM-101 and SM-102Miller Edge · US · checked 2026-09-13 · SM101-SM102_20230407

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Miller Edge official support and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.