Garage Door Repair & InstallationOpen 24 Hours — 7 Days a Week
Anderson Garage Door Service
Call for Service
(203) 902-3902

Miller Edge / Accessory reference

Miller Edge MU22: Sensing-edge profile and configuration selection

MU22 is a sensing-edge profile with a 2-by-2-inch sensing body and two top tabs for direct mounting on the described two-inch sectional-door surface. The body height excludes the tabs, and their inconsistent height conversion cannot establish clearance. Its mounting arrangement differs from the single-tab MT22 profile.

US source scopeUpdated 2026-09-15Independent Anderson reference

Match the whole number.

Manufacturer identifier: MU22. Keep every character when comparing it with your label or paperwork. A similar number does not establish the same component.

Values apply to the exact identifier and scope in the cited source.
Profile applicationCommercial sectional doors with a two-inch surface and appropriate direct mounting.
View source and citation details
Mounting arrangementTwo top tabs provide direct mounting; no separate mounting channel is required in the described arrangement.
View source and citation details
Profile width2 inches
View source and citation details
Profile height2-inch sensing body, excluding the mounting tabs
View source and citation details
MaterialsHeavy-duty reinforced PVC.
View source and citation details
Maximum electric-edge length150 feet
View source and citation details
Outlet selectionUniversal, left or right.
View source and citation details
Documented configuration choices2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored; Air-Wave non-monitored; Pneumatic non-monitored
View source and citation details
Selection boundaryA profile name does not specify the complete configured edge. Confirm the required length, mounting geometry, outlet, monitored or non-monitored switch configuration, termination and exact operator requirements with Miller Edge. This reference does not establish fitment for every door or opener.
View source and citation details
Source limitationThe larger sensing body distinguishes MU22 from MU21. The repeated 1-5/8-inch / 114-mm tab annotation is inconsistent and is not used as a clearance specification.
View source and citation details

Compare the MT22 and MU22 mounting arrangements

Both references describe nominal two-by-two-inch sensing bodies, but MT22 has one top tab for double-angle bottom bars and MU22 has two tabs for direct mounting. The inconsistent tab-height conversion remains unusable for clearance selection. Body size does not establish interchangeability.

Separate references with their own source scope. This comparison establishes no replacement or interchangeability.
Exact referenceRecorded distinctions
MT22

Miller Edge MT22: Sensing-edge profile and configuration selection

MT22 is a sensing-edge profile with a nominal 2-by-2-inch body and one top tab for the double-angle bottom bars of rolling steel and rolling fire doors. MU22 has two mounting tabs despite the same nominal body size. The inconsistent tab-height conversion cannot establish mounting clearance; confirm the actual door assembly and configured edge.

View sources and citation details
  • Profile application: Rolling steel and rolling fire doors; check the individual door assembly requirements.
    View source and citation details
  • Mounting arrangement: Single top tab between the double-angle bottom bars.
    View source and citation details
  • Profile width: 2 inches
    View source and citation details
  • Profile height: 2 inches
    View source and citation details
  • Maximum electric-edge length: 150 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored; Air-Wave non-monitored; Pneumatic non-monitored
    View source and citation details
  • Source limitation: A 2 x 2 inch MT22 body is distinct from the 2 x 1 inch MT21 and 3 x 3 inch MT33. No interchangeability is established.
    View source and citation details
  • Source limitation: The tab-height metric conversion is inconsistent in the source; confirm the actual mounting geometry.
    View source and citation details

Read MT22’s pairing status and source conditions →

MU22

This reference

Miller Edge MU22: Sensing-edge profile and configuration selection

MU22 is a sensing-edge profile with a 2-by-2-inch sensing body and two top tabs for direct mounting on the described two-inch sectional-door surface. The body height excludes the tabs, and their inconsistent height conversion cannot establish clearance. Its mounting arrangement differs from the single-tab MT22 profile.

View sources and citation details
  • Profile application: Commercial sectional doors with a two-inch surface and appropriate direct mounting.
    View source and citation details
  • Mounting arrangement: Two top tabs provide direct mounting; no separate mounting channel is required in the described arrangement.
    View source and citation details
  • Profile width: 2 inches
    View source and citation details
  • Profile height: 2-inch sensing body, excluding the mounting tabs
    View source and citation details
  • Maximum electric-edge length: 150 feet
    View source and citation details
  • Documented configuration choices: 2-wire monitored 10K; 2-wire monitored 8.2K; 2-wire monitored diode capacitor; 4-wire monitored; 2-wire non-monitored; Air-Wave non-monitored; Pneumatic non-monitored
    View source and citation details
  • Source limitation: The larger sensing body distinguishes MU22 from MU21. The repeated 1-5/8-inch / 114-mm tab annotation is inconsistent and is not used as a clearance specification.
    View source and citation details

Read MU22’s pairing status and source conditions →

A specification absent from one reference is not established by the other. Keep the exact identifier, configuration and cited revision when comparing.

Documented fitment & exclusions

Read the exact equipment or component, market, production and variant limits in every row. An omitted pairing has not been verified by this reference.

A component pairing applies only to the listed items and source conditions. It does not establish suitability for an installed opener or compatibility through another component.

Source statements and their exact conditions. Use the checker below to compare equipment or a component.
Equipment or component / relationshipEvidence and conditions
AW10

Documented compatibility

From MU22 to AW10.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 has an explicitly listed Air-Wave non-monitored option within the source-defined input group for AW10.

Applies only within this source scope
  • Market: US
  • configuration: Air-Wave non-monitored
  • Match the exact Air-Wave non-monitored profile option and its own length limit; the electric-profile length is not the pneumatic or air-wave length. Confirm the installed control and required monitoring with the manufacturer. This is a conditional component-input relationship, not whole-door approval.
  • The wired switch group supports edges up to 60 feet, but a lower limit printed for the exact edge profile takes precedence. Confirm the switch contact and circuit configuration.
AW12A

Documented compatibility

From MU22 to AW12A.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 has an explicitly listed Air-Wave non-monitored option within the source-defined input group for AW12A.

Applies only within this source scope
  • Market: US
  • configuration: Air-Wave non-monitored
  • Match the exact Air-Wave non-monitored profile option and its own length limit; the electric-profile length is not the pneumatic or air-wave length. Confirm the installed control and required monitoring with the manufacturer. This is a conditional component-input relationship, not whole-door approval.
  • The wired switch group supports edges up to 60 feet, but a lower limit printed for the exact edge profile takes precedence. Confirm the switch contact and circuit configuration.
AW14

Documented compatibility

From MU22 to AW14.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 has an explicitly listed Air-Wave non-monitored option within the source-defined input group for AW14.

Applies only within this source scope
  • Market: US
  • configuration: Air-Wave non-monitored
  • Match the exact Air-Wave non-monitored profile option and its own length limit; the electric-profile length is not the pneumatic or air-wave length. Confirm the installed control and required monitoring with the manufacturer. This is a conditional component-input relationship, not whole-door approval.
  • The wired switch group supports edges up to 60 feet, but a lower limit printed for the exact edge profile takes precedence. Confirm the switch contact and circuit configuration.
AW14-RF

Documented compatibility

From MU22 to AW14-RF.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 has an explicitly listed Air-Wave non-monitored option within the source-defined input group for AW14-RF.

Applies only within this source scope
  • Market: US
  • configuration: Air-Wave non-monitored
  • Match the exact Air-Wave non-monitored profile option and its own length limit; the electric-profile length is not the pneumatic or air-wave length. Confirm the installed control and required monitoring with the manufacturer. This is a conditional component-input relationship, not whole-door approval.
  • The radio distance is not an edge-length rating. Use the exact AW14-RF and MRF-01 system, confirm the profile length and resolve the documented receiver supply conflict.
FSC-57-115VAC

Documented compatibility

From MU22 to FSC-57-115VAC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the exact four-wire Miller Edge input group listed for FSC-57-115VAC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. This exact model specifies 115 V AC.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact four-wire monitored profile option · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • RT6 and FSC-57 safety relay controllersRT6_FSC-57_20211111, PDF page 2: Any model 4-wire Miller Edge sensing edge and model columns · checked 2026-09-14 · RT6_FSC-57_20211111 · Miller Edge
FSC-57-24VDC

Documented compatibility

From MU22 to FSC-57-24VDC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the exact four-wire Miller Edge input group listed for FSC-57-24VDC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. The VDC model and first-page list say 24 V DC; the table also says AC. AC acceptance is unresolved.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact four-wire monitored profile option · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • RT6 and FSC-57 safety relay controllersRT6_FSC-57_20211111, PDF page 2: Any model 4-wire Miller Edge sensing edge and model columns · checked 2026-09-14 · RT6_FSC-57_20211111 · Miller Edge
FSIS-35P-4

Documented compatibility

From MU22 to FSIS-35P-4.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is in the explicitly named Miller Edge 2/4-wire sensing-edge input group for FSIS-35P-4.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm exact input configuration and the full circuit with the responsible qualified designer. The group statement does not approve the edge for a classified location, establish intrinsic safety of the installation, or certify a complete door safety function.
MEL-K20

Documented compatibility

From MU22 to MEL-K20.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 falls within the MEL-K20 sheet's explicit T2 (10K) monitored sensing-edge group only with the matching configured termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • The source qualifies monitored operation with its UL325-2010 listed commercial door/gate operator context. The specific installed operator still requires confirmation; this group relationship is only the sensing-edge input scope.
  • This does not establish MEL-II or RBand compatibility, present product availability, or an installed-operator approval.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact profile monitored 10K membership · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • Monitored Edge Link MEL-K20MEL-K20_Spec_20150303, PDF page 1: Any T2 (10K) monitored edge group and listed-operator condition · checked 2026-09-14 · MEL-K20_Spec_20150303 · Miller Edge
PS20A

Documented compatibility

From MU22 to PS20A.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 has an explicitly listed Pneumatic non-monitored option within the source-defined input group for PS20A.

Applies only within this source scope
  • Market: US
  • configuration: Pneumatic non-monitored
  • Match the exact Pneumatic non-monitored profile option and its own length limit; the electric-profile length is not the pneumatic or air-wave length. Confirm the installed control and required monitoring with the manufacturer. This is a conditional component-input relationship, not whole-door approval.
  • PS20A supports pneumatic configured edges up to 18 feet; any lower profile-specific limit also applies. Match the required contact configuration.
RT6-115VAC

Documented compatibility

From MU22 to RT6-115VAC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the exact four-wire Miller Edge input group listed for RT6-115VAC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. This exact model specifies 115 V AC.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact four-wire monitored profile option · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • RT6 and FSC-57 safety relay controllersRT6_FSC-57_20211111, PDF page 2: Any model 4-wire Miller Edge sensing edge and model columns · checked 2026-09-14 · RT6_FSC-57_20211111 · Miller Edge
RT6-24VDC

Documented compatibility

From MU22 to RT6-24VDC.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the exact four-wire Miller Edge input group listed for RT6-24VDC.

Applies only within this source scope
  • Market: US
  • configuration: 4-wire monitored
  • Confirm the controller supply, edge circuit, reset requirements and installed door safety function with a qualified designer. This is component-input scope only. The VDC model and first-page list say 24 V DC; the table also says AC. AC acceptance is unresolved.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact four-wire monitored profile option · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • RT6 and FSC-57 safety relay controllersRT6_FSC-57_20211111, PDF page 2: Any model 4-wire Miller Edge sensing edge and model columns · checked 2026-09-14 · RT6_FSC-57_20211111 · Miller Edge
SM-101

Documented compatibility

From MU22 to SM-101.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the documented Miller Edge sensing-edge group for SM-101 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: Diode capacitor
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge
SM-102

Documented compatibility

From MU22 to SM-102.

Conditional

Additional source conditions or an adapter must be checked before confirming compatibility.

Details still needed
  • configuration
  • termination
  • source conditions

Use the exact label and the source scope below. An unanswered condition keeps this result conditional or unverified.

MU22 is within the documented Miller Edge sensing-edge group for SM-102 only when configured with the matching two-wire monitored termination.

Applies only within this source scope
  • Market: US
  • configuration: 2-wire monitored
  • termination: 10K resistive
  • Confirm the exact supplied termination and the installed commercial door operator requirements with Miller Edge. This is an edge-to-module input relationship, not approval of the downstream operator or a complete safety system.
  • Miller Edge MU22 sensing edgeMU22_20220607, PDF page 2: Exact profile monitored configuration membership · checked 2026-09-13 · MU22_20220607 · Miller Edge
  • Signature Module SM-101 and SM-102SM101-SM102_20230407, PDF page 2: Related-products group scope and model-specific input table · checked 2026-09-13 · SM101-SM102_20230407 · Miller Edge

Direct replacement paths

No direct successor for MU22 is verified in this reference.

A direct replacement statement does not establish reverse interchangeability, a kit equivalent or a later replacement chain.

Compare exact equipment or a component.

Check a part or accessory pairing

Loading part or accessory choices…

Selected: MU22 · Read its reference. Selection identifies a record; it does not confirm fitment.

Choose the equipment or accessory brand separately from the component brand. A missing identifier is unverified. Use the model library to identify your equipment and its source documents.

An accessory pairing, including a receiver or wall console, applies only to the exact listed pair and source conditions. It does not establish suitability for your installed opener or compatibility through another device.

Choose the equipment or accessory brand to load its published identifiers.

Use the production date on the label or records, not the purchase date. Leave blank if unknown.

Use part and model numbers only. Never enter a serial number, PIN or access code. Your entry is used for this lookup and is not put in the page address, saved in browser storage or sent to analytics.

Choose a task and enter or select an exact identifier.

Recall references

No recall reference is included for this identifier in the published dataset. This is not a safety clearance or proof that no recall exists.

Sources & scope

  1. AW10, AW12A and AW14 wired air-wave switchesMiller Edge · US · checked 2026-09-14 · AW101214_20210223
  2. AW14-RF-K10 wireless air-wave edge systemMiller Edge · US · checked 2026-09-14 · AW14RF_20210101
  3. FSIS-35P-4 intrinsically safe relay controllerMiller Edge · US · checked 2026-09-14 · FSIS-35P-4_20211111
  4. Monitored Edge Link MEL-K20Miller Edge · US · checked 2026-09-14 · MEL-K20_Spec_20150303
  5. Miller Edge MU22 sensing edgeMiller Edge · US · checked 2026-09-13 · MU22_20220607
  6. PS20A pneumatic switch and wired kit selectionMiller Edge · US · checked 2026-09-14 · PS20A_20210101
  7. PS20A and PS20-RF pneumatic systems and exact kit optionsMiller Edge · US · checked 2026-09-14 · PS20A20RF_Spec_20141208
  8. RT6 and FSC-57 safety relay controllersMiller Edge · US · checked 2026-09-14 · RT6_FSC-57_20211111
  9. Signature Module SM-101 and SM-102Miller Edge · US · checked 2026-09-13 · SM101-SM102_20230407

Anderson prepared this reference from the listed evidence. Source statements are not an Anderson installation inspection or independent product test. Official documents stay on their publisher’s website.

Related equipment guides

Browse the model library →

Confirm a missing detail

Use Miller Edge official support and match the complete part number, equipment model and production details with the source scope.

Use safely accessible labels and existing paperwork. Do not remove powered covers or adjust springs or cables to identify a component.

This is an independent Anderson reference. Manufacturer names identify the equipment and do not imply affiliation or authorized-dealer status.

A reference listing does not establish current stock, a price, eligibility for manufacturer support or that a component is faulty.